MIMF50A циклический ребут (решена) |
Здравствуйте, гость ( Вход | Регистрация )
MIMF50A циклический ребут (решена) |
15.7.2020, 22:35
Сообщение
#1
|
|
Частый гость Группа: Участники Сообщений: 42 Регистрация: 20.5.2015 Из: Ногинск Пользователь №: 19907 |
Ни с того ни с сего LIK 50А начал уходить в циклический ребут.
Проблема заключается в батарейке на MB. Логично, что севшая батарейка должна приводить к сбросу настроек, но в данной АТС это приводит к частичному сбросу, из за этого АТС уходит в цикличный ребут. Замена АКБ + сброс c SW4 OFF + заливка конфиги спасла ситуацию. Лог загрузки: Код ARMboot Bz17934_1 lge NORFLASHBOOT (Aug 12 2009 - 15:30:37)
ARMboot code: 00800000 -> 0084136c NAND CHIP : 0 NAND MID:0xec, Chip ID:0xf1 (Samsung NAND 128MB 3,3V) NAND CHIP : 1 NAND MID:0xec, Chip ID:0xf1 (Samsung NAND 128MB 3,3V) Comcerto info: CPU: M828xx EVM: SMALL SDC Version: 0x560e SDC Device ID: 0x130 Bounding option: 0xec09 CFG HZ: 132000000 NAND MSP start: 1 NAND MSP size: 31 NOR Base addr: 0x11000000 EPROM Base addr: 0x00000000 DRAM Configuration: Bank #0: 01000000 48 MB *** sdram start 0x01000000 *** sdram size 0x03000000 *** boot param addr 0x01000100 Hit Ctrl-C key to stop autoboot: 0 Start DeMerge Kernel DeMerge:: unzip MSP success [size is 1945124] DeMerge:: CSP size is 1490036 [112d34b7 >> 0176bc74] DeMerge Success (MSP) at 0x01000000, (CSP) at 0x01600000 ... Downloading MSP Image from 0x1000000 ... code_offset=0x80 code_base=8000 data_offset=cc564 code_size=cc4e4 data_base=d44e4 data_size=ec418 zeroinit_base=1c08fc prog_entry=100 AIFHEADER: BL_DecompressCode=e1a00000 BL_SelfRelocCode=e1a00000 BL_DbgInitZeroInit=eb00000c EntryPointOffset=ffff8100 ProgramExitInstr=ef000011 ImageReadOnlySize=cc4e4 ImageReadWriteSize=ec418 ImageDebugSize=1e010 ImageZeroInitSize=dd64 ImageDebugType=1de181 ImageBase=8000 WorkSpace=0 AddressMode=20 DataBase=0 FirstFatOffset=1d698c Reserved2=0 DebugInitInstr=e1a00000 ZeroInitCode[0]=e04ec00f Booting ARM0 (CSP) at 0x01600000 ... Booting ARM1 (MSP) at 0x00000100 ... Linux version 2.6.11.7-1.07.0malindi (mhryu72@ipkts-linux.ipkts.lge.com) (gcc version 3.3.2 20030820 (prerelease)) #81 Mon Mar 24 13:47:49 CST 2008 CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T) CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets Machine: ARM-M828xx Comcerto Memory policy: ECC disabled, Data cache writeback Built 1 zonelists Kernel command line: console=ttyS0,115200 root=/dev/mtdblock1 rw ip=10.33.64.30:150.150.131.139:10.33.64.1:255.255.255.224::eth0 PID hash table entries: 256 (order: 8, 4096 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 48MB = 48MB total Memory: 45336KB available (2316K code, 626K data, 308K init) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 Comcerto GPIO: init Comcerto GPIO: GPIOs configured as IRQ source(s) Comcerto PCI: init Comcerto PCI: Comcerto device is not configured in PCI host Verify that HBMODE_n(low) pin is high and HBBURSTEN_n(high) pin is low On Mindspeed MH02-D370-xxx board, remove jumper JPCISLV1 SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub SPI core: loaded version 0.2 NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. yaffs Mar 22 2008 15:26:03 Installing. Initializing Cryptographic API Crypto engine S/W registered Serial: 8250/16550 driver $Revision: 1.1.1.3 $ 2 ports, IRQ sharing disabled Serial: Comcerto 16550 serial driver $Revision: 1.4 $ ttyS0 at MMIO 0x10090000 (irq = 41) is a 16550A io scheduler noop registered loop: loaded (max 8 devices) nbd: registered device at major 43 skb pool filled with 512 skb m828xx_msp_start() stop EMAC0 control stop_emac0: already stopped m828xx_msp_ready() MSP version : $Version: m828_v2_06_4 $ msp_ready: MSP is running switch eth0 to VED mode smi_memory_phy = 6f0000 SharedMemoryRxControlStructure(PA): 0x800023c SharedMemoryRxControlStructure(VA): 0xf800023c SharedMemoryTxControlStructure(PA): 0x800023c SharedMemoryTxControlStructure(VA): 0xf800023c drivers/net/comcerto_ved.c: 1469: SetupSMIBuffers: 1280 buffers allocated Comcerto SMI: fpq(PA): 0x8001350 Comcerto SMI: fpq(VA): 0xf8001350 Comcerto SMI: fpq(PA): 0x8001370 Comcerto SMI: fpq(VA): 0xf8001370 Comcerto SMI: fpq(PA): 0x800021c Comcerto SMI: fpq(VA): 0xf800021c Comcerto SMI: fpq(PA): 0x800022c Comcerto SMI: fpq(VA): 0xf800022c Comcerto SMI: fpq(PA): 0x8001360 Comcerto SMI: fpq(VA): 0xf8001360 Comcerto SMI: fpq(PA): 0x8001380 Comcerto SMI: fpq(VA): 0xf8001380 PPP generic driver version 2.4.2 SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). mtd: NAND opt=c2ea0e34, ale-cycles=4, blk(rd=16, wr=16), ce=400000, tR=0 NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 565 at 0x0VFS: Mounted root (yaffs2 filesystem). Freeing init memory: 308K init started: BusyBox v1.01 (2006.02.06-07:50+0000) multi-call binary Starting pid 17, console /dev/console: '/etc/rc' yaffs: dev is 32505856 name is "mtdblock0" yaffs: Attempting MTD mount on 31.0, "mtdblock0" yaffs: MTD device does not support have the right page sizes yaffs: dev is 32505856 name is "mtdblock0" yaffs: Attempting MTD mount on 31.0, "mtdblock0" yaffs: dev is 32505858 name is "mtdblock2" yaffs: Attempting MTD mount on 31.2, "mtdblock2" yaffs: MTD device does not support have the right page sizes yaffs: dev is 32505858 name is "mtdblock2" yaffs: Attempting MTD mount on 31.2, "mtdblock2" yaffs: dev is 32505859 name is "mtdblock3" yaffs: Attempting MTD mount on 31.3, "mtdblock3" yaffs: MTD device does not support have the right page sizes yaffs: dev is 32505859 name is "mtdblock3" yaffs: Attempting MTD mount on 31.3, "mtdblock3" block 760 is bad ,so Try to clean!! Clean block 760 Fail!! block 837 is bad ,so Try to clean!! Clean block 837 Fail!! Thu Mar 23 13:22:00 UTC 2006 net.ipv4.ip_nonlocal_bind = 1 kernel.msgmni = 32 net.ipv4.tcp_keepalive_time = 60 tar: /execute.tar: No such file or directory rm: cannot remove `/execute.tar': No such file or directory REGISTER device SPI OK Nand chagall: ioremap nand memory SUCCESS!!! Nand : map GPIO memory SUCCESS!!! Nand : map DEV_EXT_CMU_ADDR_BASE memory SUCCESS!!! Nand : map DEV_EXT_RING_LED_ADDR_BASE memory SUCCESS!!! GPIO_PORT_RESET. GPIO_PORT_RESET >>> io_base_100de344 : read = 0x0016 >>>>>>>>>>>>>>>>>>>>>>>>>> NET: Registered protocol family 27 misc:installed... devWatchDog: module license '' taints kernel. watchdog : installed! bootenv:installed(1.Bb, mii) - sect(mac:0x3f0000, env:0x3f2000, env_back:0x3f4000) proc file supportted! board! : 00000006 sram: major number = 254 sram:installed(mfime50a), v2.5 devtwl:installed... seeprom:installed --- k_pid=41 :: kernel thread, entry devNetc:installed (crypto info: name=MSPD IPsec2, capability=null|md5|sha1|sha256|des|3des|aes) revision:2.0Au, mc-to-mc relay ======== EMAC_ARCCTRL=00000016 ippp0 added Encapsulation for ippp0 is syncppp EAZ/MSN for ippp0 is 100 Layer-2-Protocol for ippp0 is hdlc Hangup-Timeout for ippp0 is 180 sec. done [iPECS Loader] Apploader Start [iPECS Loader] Loading the Loader File [iPECS Loader] Autoloader Execute /home/_main_app1.rom from the loader file Starting System Initialization Pthread [DEBUG] Timer_1_HISR: 0 isdnloop: (loop0) DRV1.23EC-Q.931-CAPI-CNS-BASIS-20.02.96 isdnloop: (loop0) Euro-Protocol loaded and running Q[7]-[0] maxmsg[100] X msgsize[970] = Qsize[97000]->[97000]->msg_qB[97000] Q[12]-[8001] maxmsg[100] X msgsize[1024] = Qsize[102400]->[102400]->msg_qB[102400] Q[13]-[10002] maxmsg[400] X msgsize[1024] = Qsize[409600]->[409600]->msg_qB[409600] Q[11]-[18003] maxmsg[360] X msgsize[32] = Qsize[11520]->[11520]->msg_qB[11520] [Dev_Init_Task] starting init. DB ptr [Dev_Init_Task] ending init. DB ptr Mismatched IPKTS and so DB initialized!!!!---! VAINIT : dev(ipfilter), ver=2.0Au, mc-to-mc relay [ONE_IP] setup q931 ports range: 2048..2559 [ONE_IP] setup h245 ports range: 2560..3071 [ONE_IP] setup ras ports range: 2048..3071 ############################################################################ ### ### ### ======================== DSP's Info. =============================== ### ### ### ############################################################################ ST 1 : query about dev_type : 0x32, m82805 voip density=22, costG711=1.000, costG729a=4.000, costG723=4.000 ST 2 : query about dev_version : rev. B ST 3 : query about msp armcode_version : m828_v2_06_4 ST 4 : query about msp spucode_version : C64V_5_12_38 ST 5 : spucode_version verification : passed! ST 6 : initialize remain dsp parts... ST 7 : end of dsp init. [ips init]entering ptKTSProtInitialize Q[4]-[40008] maxmsg[10] X msgsize[1024] = Qsize[10240]->[10240]->msg_qB[10240] Q[6]-[48009] maxmsg[120] X msgsize[1024] = Qsize[122880]->[122880]->msg_qB[122880] Q[0]-[5000a] maxmsg[180] X msgsize[1024] = Qsize[184320]->[184320]->msg_qB[184320] Q[1]-[5800b] maxmsg[60] X msgsize[1024] = Qsize[61440]->[61440]->msg_qB[61440] Q[2]-[6000c] maxmsg[60] X msgsize[1024] = Qsize[61440]->[61440]->msg_qB[61440] Q[3]-[6800d] maxmsg[60] X msgsize[1024] = Qsize[61440]->[61440]->msg_qB[61440] Q[4]-[40008] Qsize[16384]->msg_qB[10240] Q[6]-[48009] Qsize[16384]->msg_qB[122880] [ips init]ret, ptKTSProtInitialize = 0 [ips init]entering ptMsgQOpen-RX Q[0]-[5000a] Qsize[16384]->msg_qB[184320] [ips init]entering ptMsgQOpen-TX [ips init]entering ptMsgQOpen- VOIP TX Q[1]-[5800b] Qsize[16384]->msg_qB[61440] [ips init]entering ptMsgQOpen- MSCVSF TX Q[2]-[6000c] Qsize[16384]->msg_qB[61440] [ips init]entering ptMsgQOpen- CR TX [ips init]entering ptMsgQOpen- CR RX Q[3]-[6800d] Qsize[16384]->msg_qB[61440] Q[1]-[5800b] Qsize[16384]->msg_qB[61440] Q[8]-[7000e] maxmsg[192] X msgsize[1280] = Qsize[245760]->[245760]->msg_qB[245760] Q[9]-[7800f] maxmsg[280] X msgsize[1280] = Qsize[358400]->[358400]->msg_qB[358400] Q[10]-[98013] maxmsg[120] X msgsize[84] = Qsize[10080]->[10080]->msg_qB[10080] __callid_ptr->Config F_order[X] but Valid Id exist, so cleared 3 devices !!! Watch DOG !!! by CALL !!! = 601 recover_env : entry... recover_env : exit... ARMboot Bz17934_1 lge NORFLASHBOOT (Aug 12 2009 - 15:30:37) ... |
|
|
Текстовая версия | Сейчас: 23.9.2024, 15:30 |