ARTCOM LOGO

Здравствуйте, гость ( Вход | Регистрация )

 
Ответить в данную темуНачать новую тему
> MIMF50A циклический ребут (решена)
fluturi
сообщение 15.7.2020, 22:35
Сообщение #1


Частый гость
***

Группа: Участники
Сообщений: 42
Регистрация: 20.5.2015
Из: Ногинск
Пользователь №: 19907



Ни с того ни с сего LIK 50А начал уходить в циклический ребут.

Проблема заключается в батарейке на MB.

Логично, что севшая батарейка должна приводить к сбросу настроек, но в данной АТС это приводит к частичному сбросу, из за этого АТС уходит в цикличный ребут.

Замена АКБ + сброс c SW4 OFF + заливка конфиги спасла ситуацию.


Лог загрузки:

Код
ARMboot Bz17934_1 lge NORFLASHBOOT  (Aug 12 2009 - 15:30:37)

ARMboot code: 00800000 -> 0084136c
NAND CHIP : 0
NAND MID:0xec, Chip ID:0xf1 (Samsung NAND 128MB 3,3V)
NAND CHIP : 1
NAND MID:0xec, Chip ID:0xf1 (Samsung NAND 128MB 3,3V)
Comcerto info:
  CPU:           M828xx
  EVM:             SMALL
  SDC Version:     0x560e
  SDC Device ID:   0x130
  Bounding option: 0xec09
CFG HZ:            132000000
NAND MSP start:    1
NAND MSP size:     31
NOR Base addr:     0x11000000
EPROM Base addr:   0x00000000
DRAM Configuration:
Bank #0: 01000000 48 MB
*** sdram start     0x01000000
*** sdram size      0x03000000
*** boot param addr 0x01000100
Hit Ctrl-C key to stop autoboot:  0
Start DeMerge Kernel
DeMerge:: unzip MSP success [size is 1945124]
DeMerge:: CSP size is 1490036 [112d34b7 >> 0176bc74]

DeMerge Success (MSP) at 0x01000000, (CSP) at 0x01600000 ...

Downloading MSP Image from 0x1000000 ...
code_offset=0x80
code_base=8000
data_offset=cc564
code_size=cc4e4
data_base=d44e4
data_size=ec418
zeroinit_base=1c08fc
prog_entry=100

AIFHEADER:
BL_DecompressCode=e1a00000
BL_SelfRelocCode=e1a00000
BL_DbgInitZeroInit=eb00000c
EntryPointOffset=ffff8100
ProgramExitInstr=ef000011
ImageReadOnlySize=cc4e4
ImageReadWriteSize=ec418
ImageDebugSize=1e010
ImageZeroInitSize=dd64
ImageDebugType=1de181
ImageBase=8000
WorkSpace=0
AddressMode=20
DataBase=0
FirstFatOffset=1d698c
Reserved2=0
DebugInitInstr=e1a00000
ZeroInitCode[0]=e04ec00f

Booting ARM0 (CSP) at 0x01600000 ...

Booting ARM1 (MSP) at 0x00000100 ...
Linux version 2.6.11.7-1.07.0malindi (mhryu72@ipkts-linux.ipkts.lge.com) (gcc version 3.3.2 20030820 (prerelease)) #81 Mon Mar 24 13:47:49 CST 2008
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Machine: ARM-M828xx Comcerto
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock1 rw ip=10.33.64.30:150.150.131.139:10.33.64.1:255.255.255.224::eth0
PID hash table entries: 256 (order: 8, 4096 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 48MB = 48MB total
Memory: 45336KB available (2316K code, 626K data, 308K init)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Comcerto GPIO: init
Comcerto GPIO: GPIOs configured as IRQ source(s)
Comcerto PCI: init
Comcerto PCI: Comcerto device is not configured in PCI host
    Verify that HBMODE_n(low) pin is high and HBBURSTEN_n(high) pin is low
    On Mindspeed MH02-D370-xxx board, remove jumper JPCISLV1
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
SPI core: loaded version 0.2
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
yaffs Mar 22 2008 15:26:03 Installing.
Initializing Cryptographic API
Crypto engine S/W registered
Serial: 8250/16550 driver $Revision: 1.1.1.3 $ 2 ports, IRQ sharing disabled
Serial: Comcerto 16550 serial driver $Revision: 1.4 $
ttyS0 at MMIO 0x10090000 (irq = 41) is a 16550A
io scheduler noop registered
loop: loaded (max 8 devices)
nbd: registered device at major 43
skb pool filled with 512 skb
m828xx_msp_start()
stop EMAC0 control
stop_emac0: already stopped
m828xx_msp_ready()
MSP version : $Version: m828_v2_06_4 $
msp_ready: MSP is running
switch eth0 to VED mode
smi_memory_phy = 6f0000
SharedMemoryRxControlStructure(PA): 0x800023c
SharedMemoryRxControlStructure(VA): 0xf800023c
SharedMemoryTxControlStructure(PA): 0x800023c
SharedMemoryTxControlStructure(VA): 0xf800023c
drivers/net/comcerto_ved.c: 1469: SetupSMIBuffers: 1280 buffers allocated

Comcerto SMI: fpq(PA): 0x8001350
Comcerto SMI: fpq(VA): 0xf8001350
Comcerto SMI: fpq(PA): 0x8001370
Comcerto SMI: fpq(VA): 0xf8001370
Comcerto SMI: fpq(PA): 0x800021c
Comcerto SMI: fpq(VA): 0xf800021c
Comcerto SMI: fpq(PA): 0x800022c
Comcerto SMI: fpq(VA): 0xf800022c
Comcerto SMI: fpq(PA): 0x8001360
Comcerto SMI: fpq(VA): 0xf8001360
Comcerto SMI: fpq(PA): 0x8001380
Comcerto SMI: fpq(VA): 0xf8001380
PPP generic driver version 2.4.2
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
mtd: NAND opt=c2ea0e34, ale-cycles=4, blk(rd=16, wr=16), ce=400000, tR=0
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 565 at 0x0VFS: Mounted root (yaffs2 filesystem).
Freeing init memory: 308K
init started:  BusyBox v1.01 (2006.02.06-07:50+0000) multi-call binary
Starting pid 17, console /dev/console: '/etc/rc'
yaffs: dev is 32505856 name is "mtdblock0"
yaffs: Attempting MTD mount on 31.0, "mtdblock0"
yaffs: MTD device does not support have the right page sizes
yaffs: dev is 32505856 name is "mtdblock0"
yaffs: Attempting MTD mount on 31.0, "mtdblock0"
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: MTD device does not support have the right page sizes
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: dev is 32505859 name is "mtdblock3"
yaffs: Attempting MTD mount on 31.3, "mtdblock3"
yaffs: MTD device does not support have the right page sizes
yaffs: dev is 32505859 name is "mtdblock3"
yaffs: Attempting MTD mount on 31.3, "mtdblock3"
block 760 is bad ,so Try to clean!!
Clean block 760 Fail!!
block 837 is bad ,so Try to clean!!
Clean block 837 Fail!!
Thu Mar 23 13:22:00 UTC 2006
net.ipv4.ip_nonlocal_bind = 1
kernel.msgmni = 32
net.ipv4.tcp_keepalive_time = 60
tar: /execute.tar: No such file or directory
rm: cannot remove `/execute.tar': No such file or directory
REGISTER device SPI OK
Nand chagall: ioremap nand memory SUCCESS!!!
Nand : map GPIO memory SUCCESS!!!
Nand : map DEV_EXT_CMU_ADDR_BASE memory SUCCESS!!!
Nand : map DEV_EXT_RING_LED_ADDR_BASE memory SUCCESS!!!
GPIO_PORT_RESET.
GPIO_PORT_RESET >>>
io_base_100de344 : read = 0x0016 >>>>>>>>>>>>>>>>>>>>>>>>>>
NET: Registered protocol family 27
misc:installed...
devWatchDog: module license '' taints kernel.
watchdog : installed!
bootenv:installed(1.Bb, mii) - sect(mac:0x3f0000, env:0x3f2000, env_back:0x3f4000)
      proc file supportted!
board! : 00000006
sram: major number = 254
sram:installed(mfime50a), v2.5
devtwl:installed...
seeprom:installed
--- k_pid=41
:: kernel thread, entry
devNetc:installed (crypto info: name=MSPD IPsec2, capability=null|md5|sha1|sha256|des|3des|aes)
    revision:2.0Au, mc-to-mc relay
    ======== EMAC_ARCCTRL=00000016
ippp0 added
Encapsulation for ippp0 is syncppp
EAZ/MSN for ippp0 is 100
Layer-2-Protocol for ippp0 is hdlc
Hangup-Timeout for ippp0 is 180 sec.
done
[iPECS Loader] Apploader Start
[iPECS Loader] Loading the Loader File
[iPECS Loader] Autoloader Execute /home/_main_app1.rom from the loader file

Starting System Initialization Pthread
[DEBUG] Timer_1_HISR: 0
isdnloop: (loop0) DRV1.23EC-Q.931-CAPI-CNS-BASIS-20.02.96
isdnloop: (loop0) Euro-Protocol loaded and running
Q[7]-[0] maxmsg[100] X msgsize[970] = Qsize[97000]->[97000]->msg_qB[97000]
Q[12]-[8001] maxmsg[100] X msgsize[1024] = Qsize[102400]->[102400]->msg_qB[102400]
Q[13]-[10002] maxmsg[400] X msgsize[1024] = Qsize[409600]->[409600]->msg_qB[409600]
Q[11]-[18003] maxmsg[360] X msgsize[32] = Qsize[11520]->[11520]->msg_qB[11520]
[Dev_Init_Task] starting init. DB ptr
[Dev_Init_Task] ending init. DB ptr
Mismatched IPKTS and so DB initialized!!!!---!
VAINIT : dev(ipfilter), ver=2.0Au, mc-to-mc relay
[ONE_IP] setup q931 ports range: 2048..2559
[ONE_IP] setup h245 ports range: 2560..3071
[ONE_IP] setup  ras ports range: 2048..3071

############################################################################
###                                                                      ###
### ======================== DSP's Info. =============================== ###
###                                                                      ###
############################################################################
ST 1 : query about dev_type : 0x32, m82805
       voip density=22, costG711=1.000, costG729a=4.000, costG723=4.000
ST 2 : query about dev_version : rev. B
ST 3 : query about msp armcode_version : m828_v2_06_4
ST 4 : query about msp spucode_version : C64V_5_12_38
ST 5 : spucode_version verification : passed!
ST 6 : initialize remain dsp parts...
ST 7 : end of dsp init.
[ips init]entering ptKTSProtInitialize
Q[4]-[40008] maxmsg[10] X msgsize[1024] = Qsize[10240]->[10240]->msg_qB[10240]
Q[6]-[48009] maxmsg[120] X msgsize[1024] = Qsize[122880]->[122880]->msg_qB[122880]
Q[0]-[5000a] maxmsg[180] X msgsize[1024] = Qsize[184320]->[184320]->msg_qB[184320]
Q[1]-[5800b] maxmsg[60] X msgsize[1024] = Qsize[61440]->[61440]->msg_qB[61440]
Q[2]-[6000c] maxmsg[60] X msgsize[1024] = Qsize[61440]->[61440]->msg_qB[61440]
Q[3]-[6800d] maxmsg[60] X msgsize[1024] = Qsize[61440]->[61440]->msg_qB[61440]
Q[4]-[40008] Qsize[16384]->msg_qB[10240]
Q[6]-[48009] Qsize[16384]->msg_qB[122880]
[ips init]ret, ptKTSProtInitialize = 0
[ips init]entering ptMsgQOpen-RX
Q[0]-[5000a] Qsize[16384]->msg_qB[184320]
[ips init]entering ptMsgQOpen-TX
[ips init]entering ptMsgQOpen- VOIP TX
Q[1]-[5800b] Qsize[16384]->msg_qB[61440]
[ips init]entering ptMsgQOpen- MSCVSF TX
Q[2]-[6000c] Qsize[16384]->msg_qB[61440]
[ips init]entering ptMsgQOpen- CR TX
[ips init]entering ptMsgQOpen- CR RX
Q[3]-[6800d] Qsize[16384]->msg_qB[61440]
Q[1]-[5800b] Qsize[16384]->msg_qB[61440]
Q[8]-[7000e] maxmsg[192] X msgsize[1280] = Qsize[245760]->[245760]->msg_qB[245760]
Q[9]-[7800f] maxmsg[280] X msgsize[1280] = Qsize[358400]->[358400]->msg_qB[358400]
Q[10]-[98013] maxmsg[120] X msgsize[84] = Qsize[10080]->[10080]->msg_qB[10080]
__callid_ptr->Config F_order[X] but Valid Id exist, so cleared 3 devices

!!! Watch DOG !!! by CALL !!! = 601

recover_env : entry...
recover_env : exit...



ARMboot Bz17934_1 lge NORFLASHBOOT  (Aug 12 2009 - 15:30:37)
...
Перейти в начало страницы
 
+Цитировать сообщение

Ответить в данную темуНачать новую тему
1 чел. читают эту тему (гостей: 1, скрытых пользователей: 0)
Пользователей: 0

 



Текстовая версия Сейчас: 29.3.2024, 16:59