ARTCOM LOGO

Здравствуйте, гость ( Вход | Регистрация )

 
Ответить в данную темуНачать новую тему
> Прошивка 1.0Jc, MPB 1.0Jc и Kernel 2.0Ad
AXEL
сообщение 20.1.2015, 14:43
Сообщение #1


гуру и создатель форума
********

Группа: Администраторы
Сообщений: 8680
Регистрация: 26.9.2006
Из: г.Фрязино
Пользователь №: 10



MPB

1 Wrong DTMF tone "Before
System detected wrong DTMF from SLT. It made noise in RTP packet

Now
It was fixed"
2 Tranfer feature for Mobile Extension "Before
Mobile Extension can not retrive Hold call after he transfer the call

Now
It was fixed"
3 LDP DPB "Before
LDP DPB was not operated in Canada

Now
It was fixed"
4 RFC 2833 PGM "Before

Now
The following RFC 2833 PGM is added
Board based Attributes(PGM132)
- RFC2833 Payload
- RFC2833 Volume
- RFC2833 Redundancy"
5 Maintain CPT during User Talking state. "Before

Now
1. Only the option [Line 'drop (CPT)] is applied for DISA call (before user answer).
2. The option [Maintain CPT on Talking] is appiled to both Outgoing and Incoming calls.
3. The ACNR problem which happened when the option [Maintain CPT on Talking] is 'ON' is fixed."

MPB A.0Jb(23 DEC 2014)
No Title Description
1 eMG80 - PPP IP Address 10.0.0.3 "Before
The customer network server is 10.0.0.3 and there is still an IP address conflict when the eMG80 is connected to the customers network even after PPP IP address was changed in PGM205.

Now
This is fixed."
2 eMG80 - T1 ESF mode clock change "Before
T1 clock in ESF mode is 8MHz. The calls are not completed.

Now
T1 clock is changed to 2MHz."

MPB 1.0Jc(6 JAN 2015)
No Title Description
1 Maintain CPT during User Talking state. "Before
1) ACNR feture does not work at all.
During attempt of Auto Redial the system just only seizes the analogue CO line, but does not dial the number
at all. So, there is no any dialing while ACNR attempt.
2) Now the option [Maintain CPT on user Talking] works correctly, except one case:
- Incoming call via ACO is assigned to Hunt Group
- Agent of this Hunt group answers the incoming group call
- during agent's talking state the system applies CPT detection regardless to the setiing of the option
[Maintain CPT on talking]. So, even if the option is set to OFF, then nevertheless, the CPT detection is
applied during agent is talking.

Now
This is fixed."
2 Co lines ring for no reason. "Before
Site:
The customer had an IPLDK 20 it was replaced with a eMG80.
From the start the customer experienced phantom ringing, pick up the call then one gets Exchange Dial tone.
Plug out the exchange line and re-plug the exchange line then the system will start to ring.
Connect the same exchange line on the IPLDK 20 and all ring problems is gone.

Telkom:
Telkom can simulate the same ring problem in their lab.
Disconnect the CO line and re connect the line then the system will start to ring, pick up the call then one receive exchange dial tone.

Now
It is fixed. Ring detection scheme is changed in South Africa country code(27 or *27)."


Kernel
1 Disable Telnet Daemon "Turn off the telnet daemon program on boot time.
"

Kernel 1.0Ae(16 FEB 2014)
No Title Description
1 Russia Caller ID function "ACT2 DSP image is changed to improve RCID function.
Device driver for LCO is changed with regard to RCID function."

Kernel 1.0Af(3 MAR 2014)
No Title Description
1 Russia Caller ID function ACT2 DSP image is changed to improve RCID function.
2 Polarity Reversal Detection "Problem
Incoming call was not dropped when PR is detected.

Now
Device driver for LCO is changed with regard to PR detection.
When PR is detected two times, incoming/outgoing call we be dropped if Open Loop timer is configured as non-zero value.
This change is applied only to Sweden/Spain/Denmark/Netherlands/NZ."
3 Door Open Relay "Problem
A dealer(FG Telecommunications) has reported a problem related to the function “Door Open” service.
The problem is when eMG80 is powered off and powered on (could be due to blackout or
unplugged and plugged power supply), the system activates door opener.
As a result, when the power goes off/on at night, the morning after the customer discovers his office open.
Now
This is fixed."

Kernel 1.0Ag(19 MAY 2014)
No Title Description
1 Web Access Using MODU "Before
A PPP over PSTN had only supported the feature of the remote maintenance mode.

Now
Now it supports a web access with upgrade of application revision 1.0Fd."
2 Secured RTP in VOIU GW "Before
The secured RTP was not supported in VOIU GW.

Now
Now it supports the secured RTP with upgrade of application revision 1.0Fd."

Kernel 1.0Ah(18 SEP 2014)
No Title Description
1 Call drop on LCOB when using Open Loop Timer "Problem
- Swedish default values
- P140 LCOB CO = Normal
- P141 Open Loop Timer = 10
- Make an external call
- Answer at the external part
- Now the call drops <- Problem!

Now
Device driver for LCO is changed with regard to PR detection for outgoing.
PR detection is ignored for 1 second after LCO is seized for outgoing.
"
2 Open-loop detection is line +/- polarity sensitive "Problem
With my lab test using eMG-80 ACO port 1
If pin 1 is (+) and pin 2 is (-), then Open Loop Detect is working OK
If pin 1 is (-) and pin 2 is (+), then Open Loop Detection is NOT working

Now
The change in 1.0Af is reverted for NZ.
Now, PR detection for disconnection is not used for NZ."

Kernel 2.0Ab/1.0.2 (11 NOV 2014)
No Title Description
1 Supports DHCP Client "Problem
The function of DHCP client was missed in developing eMG system.

Now
Now it was implemented with this new kernel package and application A.Ib."

Kernel 2.0Ac/1.0.3 (26 NOV 2014)
No Title Description
1 Australian compliance test : Pulse dialing Make/Break ratio "Problem
Pulse dialing Make/Break ratio was not correct when the country code is Australia or Telstra.

Now
It is fixed."

Kernel 2.0Ad/1.0.4 (24 DEC 2014)
No Title Description
1 SPR not working on outbound call "Problem
Analogue CO line has SPR enabled for Called PartyAnswer (this is working OK - tested with voltmeter)
eMG-80 has Normal Analogue CO programmed for SPR (Pgm 141 / SMDR Meter = SPR)
Outbound call duration on DKTU display does NOT re-zero when call is answered (Ver 1.0He), but does when using Ver 1.0Bb
Call duration timer is re-zero OK with SIP/ISDN lines

Now
It is fixed. This problem happened only in NZ country code."


--------------------

Хрен, положенный на мнение окружающих, обеспечивает спокойную и счастливую жизнь. (Ф.Г.Раневская)

Перейти в начало страницы
 
+Цитировать сообщение
AXEL
сообщение 20.1.2015, 14:45
Сообщение #2


гуру и создатель форума
********

Группа: Администраторы
Сообщений: 8680
Регистрация: 26.9.2006
Из: г.Фрязино
Пользователь №: 10



так же выложил новый оффлайн админ.


--------------------

Хрен, положенный на мнение окружающих, обеспечивает спокойную и счастливую жизнь. (Ф.Г.Раневская)

Перейти в начало страницы
 
+Цитировать сообщение

Ответить в данную темуНачать новую тему
1 чел. читают эту тему (гостей: 1, скрытых пользователей: 0)
Пользователей: 0

 



Текстовая версия Сейчас: 28.3.2024, 18:42