Здразвствуй, дорогой читатель данного поста..
Если ты читаешь данное письмо, то ......

Была версия:
App Version - MPB/DX86M-1.0Fe MAY/14
Boot Version - 1.0Ba NOV/13
Kernel Version - 1.0Ag
H/W Issue - 0


Станция была дефолтная. SW1.1 в OFF, SW1.2 в ON. Крышку не открывал.

Прошел визард заменил только код страны на CIS.
Залил ей кернел: GS86M21Am-Ker.rom
Перезагрузил.

Ядро обновилось:
iPECS eMG80 System
Version eMG80-R2.1.23

Снова зашел в maint залил ей: GS86M31CD_app.rom
Написало что удачно показало кнопку reset, но я на нее не нажал, а перезагрузил станцию по питанию. Никаких файлов тоже не стирал.
Теперь станция грузится, но настраивать нельзя. Ни 80, ни 443, ни telnet 5003.
Станция пингуется и все.
Еще работатет серийный порт. Пишет как грузится ... Прям критических проблем при загрузке не пишет (на мой неподготовленный взгляд)

В конце правда пишет, что файлик не может создать и ошибка драйвера.


----------------------------------------------------------------------------------------------------------------------
Вот лог загрузки:

DDR Training(1).............................................................Done

U-Boot 2013.01 (Sep 12 2015 - 13:13:52) Mindspeed $Name: uboot_7_00_5 $

I2C: ready
Flash: 4 MiB
0 ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD/Spansion S34ML02G1)
1 No NAND device found.
2 No NAND device found.
3 No NAND device found.
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Reserve MSP memory
DDR Training :
DLL_ADJ(0,1,2,3): 0x1f,0x1e,0x1c,0x1d
WR_DQS:delay0 0x7b, delay1 0x7c, delay2 0x7a, delay3 0x7b
current boot location: at SECOND
mount boot partition...
Scanning device for bad blocks
Copy boot/u-boot.bin to 0x81000000... File not found(-1)
Copy boot/boot_env to 0x80a1bb08... [DONE 8176(0x1ff0) bytes]
Net: comcerto_gemac0
Copy boot/uImage to 0x81000000... [DONE 2037156(0x1f15a4) bytes]
## Booting kernel from Legacy Image at 81000000 ...
Image Name: Linux-2.6.21.1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2037092 Bytes = 1.9 MiB
Load Address: 80808000
Entry Point: 80808000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Copy boot/msp.axf to 0x8fd00000... [DONE 1006144(0xf5a40) bytes]
Copy boot/fpp.axf to 0x8fc00000... [DONE 154968(0x25d58) bytes]

Starting kernel ...

Uncompressing Linux............................................................. ................................................................... done, bootin g the kernel.
Linux version 2.6.21.1 (wane@ipecsmg.lgericsson.com) (gcc version 3.4.6 (OpenWrt -2.0)) #77 Wed Sep 21 10:15:24 KST 2016
CPU: ARMv6-compatible processor [4117b365] revision 5 (ARMv6TEJ), cr=00c5387d
Machine: Comcerto 1000 (EVM)
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIPT write-back cache
CPU0: I cache: 65536 bytes, associativity 4, 32 byte lines, 512 sets
CPU0: D cache: 65536 bytes, associativity 4, 32 byte lines, 512 sets
Built 1 zonelists. Total pages: 55626
Kernel command line: init=/etc/preinit root=/dev/mtdblock2 rootfstype=yaffs2 rw hwaddress=eth0,B0:61:C7:03:B6:72 ip=10.10.10.2:192.168.123.215:10.10.10.1:255.25 5.255.0:ipecs-mbu:eth0:off console=ttyS0,115200 mtdparts=comcertonand:10M(boot), 64M(ppt),96M(rootfs),54M(db),-(vm0) partno=M83263G fppmode=1 firmwares=msp.axf:f 5a40@8fd00000,fpp.axf:25d58@8fc00000 membuf=sram:1900000@8e300000
Kernel command line, comcerto firmware: 'msp.axf:f5a40@8fd00000,fpp.axf:25d58@8f c00000'
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 219MB = 219MB total
Memory: 217984KB available (3232K code, 905K data, 96K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
### Board: watchdog bits: kick=27, disable=28
SPI core: loaded version 0.2
PCIe0: no device detected on link (3)
PCIe1: no device detected on link (3)
pcie_setup(0)
pcie_scan_bus(0)
PCI: bus0: Fast back to back transfers enabled
pcie_setup(1)
pcie_scan_bus(1)
PCI: bus1: Fast back to back transfers enabled
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: timer3 clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
arm1: Module loaded.
NetWinder Floating Point Emulator V0.97 (double precision)
squashfs: version 3.0 (2006/03/15) Phillip Lougher
NTFS driver 2.1.28 [Flags: R/W DEBUG].
yaffs: yaffs built Mar 2 2015 08:00:10 Installing.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10090000 (irq = 41) is a 16550A
serial8250.0: ttyS1 at MMIO 0x10094000 (irq = 58) is a 16550A
loop: loaded (max 8 devices)
nbd: registered device at major 43
C1K-MDIO-BUS-0: probed
C1K-MDIO-BUS-1: probed
c1k_eth_probe: gemac 0
-+ board_phy_setup: eth0 phyid(0022 1513) OUI=885 model=11 rev=3
eth0: C1000 Ethernet Controller b0:61:c7:03:b6:72
c1k_eth_probe: gemac 1
-+ board_phy_setup: eth2 phyid(8000 0001) OUI=200000 model=0 rev=1
eth2: C1000 Ethernet Controller 00:40:5a:00:00:01
iPECS-KSZ8401NL: Registered new driver
>>> PHY PROBE eth2: stop the PHY, dummy
iPECS-DUMMY: Registered new driver
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
SCSI Media Changer driver v0.25
ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD/Spansion S34ML02G1)
Scanning device for bad blocks
5 cmdlinepart partitions found on MTD device comcertonand
Creating 5 MTD partitions on "comcertonand":
0x000000000000-0x000000a00000 : "boot"
0x000000a00000-0x000004a00000 : "ppt"
0x000004a00000-0x00000aa00000 : "rootfs"
0x00000aa00000-0x00000e000000 : "db"
0x00000e000000-0x000010000000 : "vm0"
No NAND device found.
No NAND device found.
No NAND device found.
tdi_reset: set Streaming disable mode
tdi_reset: set Streaming disable mode
comcerto-ehci comcerto-ehci.1: comcerto EHCI
comcerto-ehci comcerto-ehci.1: new USB bus registered, assigned bus number 1
comcerto-ehci comcerto-ehci.1: irq 5, io mem 0x0f000000
tdi_reset: set Streaming disable mode
comcerto-ehci comcerto-ehci.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
rtc-pcf8563 0-0051: chip found, driver version 0.4.2
rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
TCP westwood registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing NETLINK_KEY socket
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
rtc-pcf8563 0-0051: setting the system clock to 2016-07-09 08:28:06 (1468052886)
c1k_eth_open: eth0
Disabling GEM0 delay
PHY start: 0:01
IP-Config: Complete:
device=eth0, addr=10.10.10.2, mask=255.255.255.0, gw=10.10.10.1,
host=ipecs-mbu, domain=, nis-domain=(none),
bootserver=192.168.123.215, rootserver=192.168.123.215, rootpath=
yaffs: dev is 32505858 name is "mtdblock2" rw
yaffs: passed flags ""
yaffs: yaffs: Attempting MTD mount of 31.2,"mtdblock2"
yaffs: yaffs_read_super: is_checkpointed 0
VFS: Mounted root (yaffs2 filesystem).
Freeing init memory: 96K
### update shell: nothing to do...
- preinit -
- init -
/etc/init.d/rcS: line 21: /etc/rc.d/S01syslog: not found
yaffs: dev is 32505856 name is "mtdblock0" rw
yaffs: passed flags ""
yaffs: yaffs: Attempting MTD mount of 31.0,"mtdblock0"
yaffs: auto selecting yaffs2
yaffs: yaffs_read_super: is_checkpointed 0
yaffs: dev is 32505859 name is "mtdblock3" rw
yaffs: passed flags ""
yaffs: yaffs: Attempting MTD mount of 31.3,"mtdblock3"
yaffs: auto selecting yaffs2
yaffs: yaffs_read_super: is_checkpointed 0
yaffs: dev is 32505857 name is "mtdblock1" rw
yaffs: passed flags ""
yaffs: yaffs: Attempting MTD mount of 31.1,"mtdblock1"
yaffs: auto selecting yaffs2
yaffs: yaffs_read_super: is_checkpointed 0
yaffs: dev is 32505860 name is "mtdblock4" rw
yaffs: passed flags ""
yaffs: yaffs: Attempting MTD mount of 31.4,"mtdblock4"
yaffs: auto selecting yaffs2
yaffs: yaffs_read_super: is_checkpointed 0
# remove unnecessary files... ############################
fuse init (API version 7.8)
ip_tables: © 2000-2006 Netfilter Core Team
ip6_tables: © 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1752 buckets, 14016 max)
ctnetlink v0.93: registering with nfnetlink.
ip6t_ROUTE: module license 'unspecified' taints kernel.
ipecs_misc: installed(drv=1.1.2, fpga=3)...
options:
c1k_eth_open: eth2
Disabling GEM1 delay
PHY start: 1:02
fpp_running=365 voib_installed=0 eth2_running=61
Installing DCI modules...
CSM Driver version 4.08.1cvs 13:22:37 Jul 24 2013
Comcerto 1000 architecture
Comcerto 1000 architecture
Comcerto 1000 architecture
Comcerto 1000 architecture
csm: found csm type 9 (minor 0, index 0)
csm: found csm type 9 (minor 1, index 1)
IP Interface Driver version 1.0 13:22:39 Jul 24 2013
Matisse Driver version 4.08.1cvs 13:22:32 Jul 24 2013
MSP is running
drivers/net/comcerto/comcerto_ved.c: 577: info
Device=170
Revision=0
spu_version=Arm11DspV_5_6_98
CSPtoMSPQueuePhyaddr=a000500
MSPtoCSPQueuePhyaddr=a000510
SMRXCSPhyaddr=a000520
SMTXCSPhyaddr=a000520

MSP version is : Test_74757_1

ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/none/1.1.2.2 loaded
PPP BSD Compression module registered
ipecs_rtc: installed...
ipecs_sram: hd_sect=512, nsect=51200
ipecs_sram: major number = 254
- wrap_init: device wrap malloc=40000 for 8192 nodes
- wrap_init: device stat malloc=18000 for 8192 nodes
ipecs_sram: installed(size=25MB), v=3.0.0.0
membuf: pa/va=8e300000/d0000000
:: sram wrapper kthread, entry, dev=ce241000
ipecs_e2p: installed(drv=1.0.0, fpga=3)...
ipecs_env: installed(env_valid=1)...
SPI core: add adapter comcerto-spi
SPI core: add driver ipecs_spi
SPI core: attach client to adapter comcerto-spi
ipecs_spi: installed(ver=1.2.0)...
ipecs_wdog: installed(2.0Aa, wdog-tmr), HZ=200
isdnloop-ISDN-driver Rev 1.11.6.7
Register LDKPPP Device Driver.
ver=1.0Aa
isdnloop: (loop0) virtual card added
ipecs_net: local dev name=eth0
ipecs_net: dsp dev name=eth1
ipecs_net: loop dev name=lo
ipecs_net: VVMU/VOIB48 dev name=eth2
net device ptr:
eth=cda13000 dsp=c03dd81c lo=c03ddf9c eth2=cda6a800
vlan=0
ipecs_net: installed (HZ=200, ms=5)
revision: 3.5Ca, SRTP-SESSION-TRAIN
ipecs_dpram: installed, dpram map: xxxx...
REGISTER devAct2 device 0.1.1 OK
REGISTER devSlot device 0.1.1 OK
[FPGA Iss.3] CMU Detection lco_io_base[0][4] = 0xce70000f
REGISTER devLco device 0.1.12 OK
REGISTER devTimer device 0.1.1 OK
ISDN Drv Ver:A.0Ad-b03 Date:27 JUL 2015
REGISTER device ipecs_pri 0.0.2 OK
Register device ipecs_igpio 0.0.1 OK
REGISTER device ipecs_bri 0.0.1 OK
[IDEV]dev_irq_status = ce800006(ff)
[BDEV]basic borad id = FF
[BDEV]opt1 borad id = FF
[BDEV]opt2 borad id = FF
[BDEV]brib_opt1_io_base = ce0d0000
[BDEV]brib_opt2_io_base = ce0d4000
[BDEV]brib_basic_io_base = ce0d8000
[BDEV]peb_io_base[0] = ce0d8200
[BDEV]peb_io_base[1] = ce0d8300
[BDEV]peb_io_base[2] = ce0d0400
[BDEV]peb_io_base[3] = ce0d0600
[BDEV]peb_io_base[4] = ce0d4400
[BDEV]peb_io_base[5] = ce0d4600
[PDEV]fpga_base_address = ce0c8000
[PDEV]pef_base_address = ce0c8100
[PDEV]c5402_base_address = ce0c8200
[PDEV]dev_brd_id = ce0c8000
[PDEV]dev_cntry_var = ce0c8000
[PDEV]dev_brd_iss = ce0c8001
[PDEV]dev_fpga_ver = ce0c8002
[PDEV]dev_pp_reset = ce0c8003
[PDEV]dev_dip_sw = ce0c8004
[PDEV]dev_led1 = ce0c8005
[PDEV]dev_led2 = ce0c8006
[BDEV]Line Mode : FF(1:T, 0:S)

[BDEV]Slot#0 BrdId=0x1F=>0x00

[BDEV]Slot#1 BrdId=0x1F=>0x00

[BDEV]Slot#2 BrdId=0x1F=>0x00
ipecs_timer: installed(1.0.0, hwtmr=5ms)...
ippp0 added
Encapsulation for ippp0 is syncppp
EAZ/MSN for ippp0 is 100
Layer-2-Protocol for ippp0 is hdlc
Hangup-Timeout for ippp0 is 180 sec.
-+ isdnloop_command:1276: carrier off...
carrier=0
done
kernel.msgmni = 32
net.ipv4.ip_nonlocal_bind = 1
net.ipv4.tcp_keepalive_time = 60
net.netfilter.nf_conntrack_udp_timeout = 1
VOIB: board is not installed...
[app.tar.gz] is not exist. skip app extraction.
end of app file extraction.
end of html file extraction.
isdnloop: (loop0) DRV1.23EC-Q.931-CAPI-CNS-BASIS-20.02.96
isdnloop: (loop0) Euro-Protocol loaded and running
g_fdDipSw = 3 dip = b
ipmethod =
dhcpContinue stop
DHCP wait 3 sec
DHCP Loop End
###########################################################
###########################################################
[iPECS Loader] Apploader Start
[iPECS Loader] Loading the Loader File
[iPECS Loader] Autoloader Execute /home/http/_main_app2.rom from the loader file

Starting System Initialization...

mainsub_start_itimer::::: magic number=3355aacc time=2000 -> 10
> application init. started...
[BOARD_INFO] board=iPECS eMG80, co_opt=NONE
[BOARD_INFO] No_Of_Stns[140] No_Of_Cols[74] No_Of_Stns_And_Cols[214] IpExtensionTotalNumFlag[0]
Q[7]-[0] msg_key[6b:107] maxmsg[200] X msgsize[970] = Qsize[194000]->[194000]->msg_qB[194000]
Q[12]-[8001] msg_key[70:112] maxmsg[200] X msgsize[1024] = Qsize[204800]->[204800]->msg_qB[204800]
Q[13]-[10002] msg_key[71:113] maxmsg[400] X msgsize[1024] = Qsize[409600]->[409600]->msg_qB[409600]
Q[11]-[18003] msg_key[6f:111] maxmsg[1050] X msgsize[32] = Qsize[33600]->[33600]->msg_qB[33600]
[DevMisc_Init]FPGA VER : 3
open ipecs_spi file : g_fdSpi 8
DevMisc_Init!!! (Codec:A-law)
DevAct2IO_Init!!!
DevAct2IO_Init!!!
DevLcoIO_Init(1)!!!
DevLcoIO_Init(2)!!!
DevLcoIO_Init(3)!!!
DevLcoIO_Init(4)!!!
DevLcoIO_Init(5)!!!
DevLcoIO_Init(6)!!!
DevLcoIO_VoipDtmf!!!
MGIO_Initialize!!!
g_fdRTC(128) open /dev/ipecs_rtc
SRAM_INIT: sram DB, init...
[PROT_INIT] driver major #=254
[PROT_INIT] db: prefix=__DB_file__
[PROT_INIT] db: configuration file=__DB_file__config_
[PROT_INIT] db: create partitions...
[PROT_INIT] db: open partitions...
elapsed time=1.182s
[PROT_INIT] db: mmap(size=0x72c000)...
[PROT_INIT] db: msync bitmap, max=1836
[PROT_INIT] db: mmap=40004000 size=0072c000
[PROT_INIT] db: PROT_END - PROT_BASE = 0072b330 - 00001000 = 0072a330
[PROT_INIT] db: ADDR_END - ADDR_BASE = 40730000 - 40005000 = 0072b000
SRAM_INIT: sram DB, mmap=40004000 size=0072c000
[Dev_Init_Task] starting init. DB ptr
[Dev_Init_Task] ending init. DB ptr 0x4072f330 - 0x40005000 = 72a330 = 7336 KB
------- SYS_EMG: TODO!!!: VLAN SET -------- main_sub.c:1712
DHCP OFF by env(kill dhcpcd)!!!
[GetMACAddrEth0:679] b0:61:c7:3:b6:72
Mfim_ip_addr=a0a0a02
Mfim_net_mask=ffffff00
Mfim_firewall_ip_addr=0
[SYS_CTRL] lan1: net=10.10.10.2/255.255.255.0/10.10.10.1
[INIT ETH2: ifconfig Return(0)] ip: 1020304, net mask:0, gateway: 0, mac:00:40:5a:00:00:01
VAINIT : dev(ipfilter), ver=3.5Ca, SRTP-SESSION-TRAIN
[ONE_IP] setup q931 ports range: 2048..2559
[ONE_IP] setup h245 ports range: 2560..3071
[ONE_IP] setup ras ports range: 2048..3071
[ONE_IP] setup sip tcp ports range: 3072..4095
VAINIT : CSMENCAPS TYPE(0)
[DCI_RcvThread] Comcerto 1000 architecture
started
[DCI_OPEN] device state=0, resetting...
[DCI_OPEN] open dev=294

############################################################################
### ###
### ======================== DSP's Info. =============================== ###
### ###
############################################################################
ST 1 : query about dev_type : 0x53, m83xxx
ST 2 : query about dev_version : rev. A
ST 3 : query about msp armcode_version : Test_74757_1
ST 4 : query about msp spucode_version : Arm11DspV_5_6_98
ST 5 : spucode_version verification : passed!
ST 6 : initialize remain dsp parts...
ST 7 : rtp ports(4): (7000, 7015) (7100, 7115) (7132, 7147) (7200, 7299)
ST 8 : end of dsp init.
[SYS_CTRL] system dynamic port range: 4096..6095
------- SYS_EMG/UCP: TODO!!!: main_sub.c:3546
[ips init]entering ptKTSProtInitialize
[GetMACAddrEth0:679] b0:61:c7:3:b6:72
Q[4]-[40008] msg_key[68:104] maxmsg[10] X msgsize[1024] = Qsize[10240]->[10240]->msg_qB[10240]
Q[6]-[48009] msg_key[6a:106] maxmsg[120] X msgsize[1024] = Qsize[122880]->[122880]->msg_qB[122880]
Q[0]-[5000a] msg_key[64:100] maxmsg[180] X msgsize[1024] = Qsize[184320]->[184320]->msg_qB[184320]
Q[3]-[5800b] msg_key[67:103] maxmsg[60] X msgsize[1024] = Qsize[61440]->[61440]->msg_qB[61440]
[ptInitTCPConnInfoHash] g_tTCPConnInfoSema = (nil)
[ptInitTCPConnInfoHash:1665] g_tTCPConnInfoSema[(nil)] wait
[ptInitTCPConnInfoHash:1671] g_tTCPConnInfoSema[(nil)] post
Q[4]-[40008] msg_key[68:104] Qsize[16384]->msg_qB[10240]
[ips_init] net0 bind address: 10.10.10.2:5588
[ips_init] net1 bind address: 1.2.3.4:5588
Q[6]-[48009] msg_key[6a:106] Qsize[16384]->msg_qB[122880]
[ips init]ret, ptKTSProtInitialize = 0
[ips init]entering ptMsgQOpen-RX
Q[0]-[5000a] msg_key[64:100] Qsize[16384]->msg_qB[184320]
[ips init]entering ptMsgQOpen-TX
[ips init]entering ptMsgQOpen- CR TX
[ips init]entering ptMsgQOpen- CR RX
Q[3]-[5800b] msg_key[67:103] Qsize[16384]->msg_qB[61440]
Q[8]-[6000c] msg_key[6c:108] maxmsg[2600] X msgsize[1280] = Qsize[3328000]->[16384]->msg_qB[16384]
[VINFO] (-1) vm_Initialize, check crypto function -> ok
[VINFO] (-1) vm_Initialize, srtp supporting -> 1
[VINFO] (-1) vm_Initialize, set the bit for the srtp supporting...
[VINFO] (-1) vm_Initialize, crypto supporting2 -> 0x3
[VINFO] (-1) vm_Initialize, create VOIP GW thread...
(INIT_H323) HBINFO: network, local-ip=10.10.10.2
(INIT_H323) HBINFO: network, wan-ip=10.10.10.2
(INIT_H323) HBINFO: network, media-ip=10.10.10.2
(INIT_H323) HBINFO: Iinit. with endpoint type : GATEWAY...
Q[10]-[80010] msg_key[6e:110] maxmsg[1000] X msgsize[180] = Qsize[180000]->[180000]->msg_qB[180000]
(INIT_H323) HBINFO: End of init., w/o GK config...
EKSU Not Installed!!!
BKSU PP/ACT2 Reset!
Act2(#0) GSXD Init OK
Act2(#0) DBID Init OK
Act2(#0) GSL12 Init OK
[AsicDspMemoryCheck]Code Compare Success!!!
First Main Act2 Init-Complete Ver(1.6)
SLOT7(0x00) ResetSpiLco:BMBU LCO/SLT(0xf7)!!!
tmpBoardId(S#0) = 0x1
[SLIB] SLOT0 DuSLIC feeding power ON!
tmpBoardId(S#1) = 0xff
tmpBoardId(S#2) = 0xff
tmpBoardId(S#3) = 0xff
tmpBoardId(S#4) = 0xff
tmpBoardId(S#5) = 0xff
MBU LCOB INSTALLED
tmpBoardId(S#6) = 0x8
tmpBoardId(S#7) = 0xff
tmpBoardId(S#8) = 0xff
tmpBoardId(S#9) = 0xff
tmpBoardId(S#10) = 0xff
tmpBoardId(S#11) = 0xff
SLOT0 VOIB8 Dev-malloc() success
SLOT0 VOIB8 Dev-malloc() success
NIPP : g_usNationCode = 82ff [KOR:82ff]
NIPP : OptionBID = ff [NONE]
UCP : Spi device file open
UCP : devSpi open SUCCESS!
UCP100 Nipp Channel : fxs=2, fxo=0, fxd=8, fxc=0
UCP100 FXC start Channel : 10
g_siMCSocket : 439
DUAL_FILTER_ECAN >>> FALSE
[IDEV]ipecs_igpio Open
[BAPP]igpio file
[IBDEV]BRIU=0x1F
open : 0x1B8

[IBDEV]BRIU_Type=0x07
[BAPP]BRIU board
[IBDEV]BH2/1#1=0x1F
id:0x1F, type:7
[IBDEV]BH2/1#1_Type=0x07

[BAPP]BH2/1#1 bo
[IBDEV]BH2/1#2=0x1F
ard id:0x1F, typ
[IBDEV]BH2/1#2_Type=0x07
e:7
[BAPP]BH2/1#2 board id:0x1F, type:7
[BAPP]Total BCH Num:0
Wrapup Task Interval = 3 => 30 msec
LED Task Interval = 12 => 120 msec
LCD Task Interval = 30 => 300 msec
iPKTS Retransmission = 4
LEDLCD Devide Number = 3
Kernel :: Kernel Version is [R1.1.13] in rc file.
[SDC_Init_Port] ttyS0, fd=441, br=115200, hflow=0, xon/off=0
[SDC_Init_Port] ttyS1, fd=442, br=115200, hflow=0, xon/off=0
[SDC_Init_Port] ttyUSB0, fd=-1, br=115200, hflow=0, xon/off=0
[SDC_Init_Port] ttyUSB1, fd=-1, br=115200, hflow=0, xon/off=0

iPECS eMG80 System.
Copyright © 2012
Ericsson-LG Enterprise.
Port Name:COM1 Date: 07/09/16 Time: 08:28:30
Version: eMG80-R2.1.23, Checksum: 0

SW1 BACKUP DATABASE: THE SYSTEM DATABASE WAS NOT RESTORED TO DEFAULT!
* Reset_cnt = 47
############## Last Reset Cause = POWER OFF ###############
########### NO LAST log
############## Last Reset Cause = POWER OFF ###############
------[main_sub.c:InitSystemResource:2081] msync: all=3 range=8379
------[main_sub.c:InitSystemResource:2086] init. time DB msync all: elapsed time=0.000s
[GetMACAddrEth0:679] b0:61:c7:3:b6:72
eth0: c1k_eth_close
c1k_eth_open: eth0
Disabling GEM0 delay
PHY start: 0:01
ADDRCONF(NETDEV_UP): eth0: link is not ready
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1151 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1155 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1159 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1163 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1167 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1171 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1175 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1179 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1182 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1186 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1189 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1214 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1230 Status:0
---- DPRAM: 0 0 0 0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1255 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1266 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1271 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1283 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1288 Status:0

*** Start nippmg_thread ***
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1291 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1308 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1312 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1317 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1324 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1332 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1338 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1341 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1347 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1353 Status:0
[DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1358 Status:0
*** Start NIP PRIB Main ***

*** Start LLDP-MED ***
-+ LLDPService: add LLDP MAC A
lldp Comp : 2016/11/09 09:30:44 by bhchoi
lldp Date : 2016/11/09 09:30:44

lldp year : 2016, month : 11, day : 09
RdPsysDiffServPreTaggingMfim : 4
RdPsysVlanOnOff : 0
RdPsysVlanPriority : 0
RdPsysVlanId : 0

*** Start nippmg_slib_task ***
nippmg_slib_semaphore init ret=0
[XMLHttpWebserverStart] : >>>>>>>>>>>>>>>>
[RegisterNippBoard] P_Slot[12].CallBoardId = 0x0
[RegisterNippBoard] P_Slot[13].CallBoardId = 0x0
startNippBoardEvent
------ mmap tmr start...
[MODU PPP] options.ttyS1 to be updated
AAAAAAA OSS ASN.1 (QSIG) is initialized.
[MODU PPP] tty1_options, result = 740
AAAAAAA OSS ASN.1 (H450) is initialized.
[VSF] misc_vsf task Start ...
[GetMACAddrEth0:679] b0:61:c7:3:b6:72
brim task will be terminated !!
isdn_free_channel: called with invalid drv(-1) or channel(-1)

********************************
* Option MEMU : not installed *
********************************

mkdir: can't create directory '/var/lock': File exists
[MODU PPP] ifconfig ippp0 down
[VSF] old usr msg header conversion start...
[Nipp PRIB] Can't Open Driver!!!
fNippIsrStart
[VSF] old usr msg header conversion finished, total_usr_msg=0, converted=0, time=356 msec

SLT ports Duslic Initial Results
----------------------------------------
SLOT port Duslic_status
----------------------------------------
SLOT0 00..07 30 30 30 30 30 30 30 30
SLOT1 10..0f
SLOT2 20..1f
SLOT3 30..2f
SLOT4 40..3f
SLOT5 50..4f
----------------------------------------
Duslic fault : 0 port(s)
PHY: 0:01 - Link is Up - 100/Full
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

--------------------------------------------------------------------------------------------------

Подскажите, что делать?

Сонсолью тоже соединялся PuTTY.
Авторизуюсь j...., (1234 - не подходит) но никаких пунтных подстазок нет.
Системного аппарата тоже нет(

Вероятно, рекавери поможет. К сожалению, у меня нет.
Из каких же таких соображений вы обесточили АТС в процессе ее обновления? Кнопочка Reset не просто так же сделана...

А SW1.2 переводили в OFF после выставления страны и перезагрузке? Перезагружали с SW1.2 = ON для сброса настроек по дефолту?

Ну нативно кнопка резет выглядит как отменить все изменения на странице. Вот почему.
SW1.2 был всю дорогу в ON.

После потери связи со станцией он был уже и в ON и в OFF. Но ничего путного не вышло.

Спасибо отзывчивым людям.
Буду заниматься рекавери.

Залил рекавери. Все ожило.
Спасибо.

Я так подозреваю что удалили файлы перед UPGRADE.
Это делать не надо.