Убил станцию, После перепрошивки нет возможности зайти на станцию |
Здравствуйте, гость ( Вход | Регистрация )
Убил станцию, После перепрошивки нет возможности зайти на станцию |
22.2.2017, 18:17
Сообщение
#1
|
|
Участник Группа: Участники Сообщений: 18 Регистрация: 24.1.2017 Пользователь №: 20544 |
Здразвствуй, дорогой читатель данного поста..
Если ты читаешь данное письмо, то ...... Была версия: App Version - MPB/DX86M-1.0Fe MAY/14 Boot Version - 1.0Ba NOV/13 Kernel Version - 1.0Ag H/W Issue - 0 Станция была дефолтная. SW1.1 в OFF, SW1.2 в ON. Крышку не открывал. Прошел визард заменил только код страны на CIS. Залил ей кернел: GS86M21Am-Ker.rom Перезагрузил. Ядро обновилось: iPECS eMG80 System Version eMG80-R2.1.23 Снова зашел в maint залил ей: GS86M31CD_app.rom Написало что удачно показало кнопку reset, но я на нее не нажал, а перезагрузил станцию по питанию. Никаких файлов тоже не стирал. Теперь станция грузится, но настраивать нельзя. Ни 80, ни 443, ни telnet 5003. Станция пингуется и все. Еще работатет серийный порт. Пишет как грузится ... Прям критических проблем при загрузке не пишет (на мой неподготовленный взгляд) В конце правда пишет, что файлик не может создать и ошибка драйвера. ---------------------------------------------------------------------------------------------------------------------- Вот лог загрузки: DDR Training(1).............................................................Done U-Boot 2013.01 (Sep 12 2015 - 13:13:52) Mindspeed $Name: uboot_7_00_5 $ I2C: ready Flash: 4 MiB 0 ONFI flash detected ONFI param page 0 valid NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD/Spansion S34ML02G1) 1 No NAND device found. 2 No NAND device found. 3 No NAND device found. NAND: 256 MiB In: serial Out: serial Err: serial Reserve MSP memory DDR Training : DLL_ADJ(0,1,2,3): 0x1f,0x1e,0x1c,0x1d WR_DQS:delay0 0x7b, delay1 0x7c, delay2 0x7a, delay3 0x7b current boot location: at SECOND mount boot partition... Scanning device for bad blocks Copy boot/u-boot.bin to 0x81000000... File not found(-1) Copy boot/boot_env to 0x80a1bb08... [DONE 8176(0x1ff0) bytes] Net: comcerto_gemac0 Copy boot/uImage to 0x81000000... [DONE 2037156(0x1f15a4) bytes] ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux-2.6.21.1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2037092 Bytes = 1.9 MiB Load Address: 80808000 Entry Point: 80808000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Copy boot/msp.axf to 0x8fd00000... [DONE 1006144(0xf5a40) bytes] Copy boot/fpp.axf to 0x8fc00000... [DONE 154968(0x25d58) bytes] Starting kernel ... Uncompressing Linux............................................................. ................................................................... done, bootin g the kernel. Linux version 2.6.21.1 (wane@ipecsmg.lgericsson.com) (gcc version 3.4.6 (OpenWrt -2.0)) #77 Wed Sep 21 10:15:24 KST 2016 CPU: ARMv6-compatible processor [4117b365] revision 5 (ARMv6TEJ), cr=00c5387d Machine: Comcerto 1000 (EVM) Memory policy: ECC disabled, Data cache writeback CPU0: D VIPT write-back cache CPU0: I cache: 65536 bytes, associativity 4, 32 byte lines, 512 sets CPU0: D cache: 65536 bytes, associativity 4, 32 byte lines, 512 sets Built 1 zonelists. Total pages: 55626 Kernel command line: init=/etc/preinit root=/dev/mtdblock2 rootfstype=yaffs2 rw hwaddress=eth0,B0:61:C7:03:B6:72 ip=10.10.10.2:192.168.123.215:10.10.10.1:255.25 5.255.0:ipecs-mbu:eth0:off console=ttyS0,115200 mtdparts=comcertonand:10M(boot), 64M(ppt),96M(rootfs),54M(db),-(vm0) partno=M83263G fppmode=1 firmwares=msp.axf:f 5a40@8fd00000,fpp.axf:25d58@8fc00000 membuf=sram:1900000@8e300000 Kernel command line, comcerto firmware: 'msp.axf:f5a40@8fd00000,fpp.axf:25d58@8f c00000' PID hash table entries: 1024 (order: 10, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 219MB = 219MB total Memory: 217984KB available (3232K code, 905K data, 96K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 ### Board: watchdog bits: kick=27, disable=28 SPI core: loaded version 0.2 PCIe0: no device detected on link (3) PCIe1: no device detected on link (3) pcie_setup(0) pcie_scan_bus(0) PCI: bus0: Fast back to back transfers enabled pcie_setup(1) pcie_scan_bus(1) PCI: bus1: Fast back to back transfers enabled Generic PHY: Registered new driver SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: timer3 clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered arm1: Module loaded. NetWinder Floating Point Emulator V0.97 (double precision) squashfs: version 3.0 (2006/03/15) Phillip Lougher NTFS driver 2.1.28 [Flags: R/W DEBUG]. yaffs: yaffs built Mar 2 2015 08:00:10 Installing. io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x10090000 (irq = 41) is a 16550A serial8250.0: ttyS1 at MMIO 0x10094000 (irq = 58) is a 16550A loop: loaded (max 8 devices) nbd: registered device at major 43 C1K-MDIO-BUS-0: probed C1K-MDIO-BUS-1: probed c1k_eth_probe: gemac 0 -+ board_phy_setup: eth0 phyid(0022 1513) OUI=885 model=11 rev=3 eth0: C1000 Ethernet Controller b0:61:c7:03:b6:72 c1k_eth_probe: gemac 1 -+ board_phy_setup: eth2 phyid(8000 0001) OUI=200000 model=0 rev=1 eth2: C1000 Ethernet Controller 00:40:5a:00:00:01 iPECS-KSZ8401NL: Registered new driver >>> PHY PROBE eth2: stop the PHY, dummy iPECS-DUMMY: Registered new driver PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered MPPE/MPPC encryption/compression module registered NET: Registered protocol family 24 SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). SCSI Media Changer driver v0.25 ONFI flash detected ONFI param page 0 valid NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD/Spansion S34ML02G1) Scanning device for bad blocks 5 cmdlinepart partitions found on MTD device comcertonand Creating 5 MTD partitions on "comcertonand": 0x000000000000-0x000000a00000 : "boot" 0x000000a00000-0x000004a00000 : "ppt" 0x000004a00000-0x00000aa00000 : "rootfs" 0x00000aa00000-0x00000e000000 : "db" 0x00000e000000-0x000010000000 : "vm0" No NAND device found. No NAND device found. No NAND device found. tdi_reset: set Streaming disable mode tdi_reset: set Streaming disable mode comcerto-ehci comcerto-ehci.1: comcerto EHCI comcerto-ehci comcerto-ehci.1: new USB bus registered, assigned bus number 1 comcerto-ehci comcerto-ehci.1: irq 5, io mem 0x0f000000 tdi_reset: set Streaming disable mode comcerto-ehci comcerto-ehci.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core rtc-pcf8563 0-0051: chip found, driver version 0.4.2 rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0 TCP westwood registered NET: Registered protocol family 1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver sit0: Disabled Privacy Extensions NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing NETLINK_KEY socket 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> rtc-pcf8563 0-0051: setting the system clock to 2016-07-09 08:28:06 (1468052886) c1k_eth_open: eth0 Disabling GEM0 delay PHY start: 0:01 IP-Config: Complete: device=eth0, addr=10.10.10.2, mask=255.255.255.0, gw=10.10.10.1, host=ipecs-mbu, domain=, nis-domain=(none), bootserver=192.168.123.215, rootserver=192.168.123.215, rootpath= yaffs: dev is 32505858 name is "mtdblock2" rw yaffs: passed flags "" yaffs: yaffs: Attempting MTD mount of 31.2,"mtdblock2" yaffs: yaffs_read_super: is_checkpointed 0 VFS: Mounted root (yaffs2 filesystem). Freeing init memory: 96K ### update shell: nothing to do... - preinit - - init - /etc/init.d/rcS: line 21: /etc/rc.d/S01syslog: not found yaffs: dev is 32505856 name is "mtdblock0" rw yaffs: passed flags "" yaffs: yaffs: Attempting MTD mount of 31.0,"mtdblock0" yaffs: auto selecting yaffs2 yaffs: yaffs_read_super: is_checkpointed 0 yaffs: dev is 32505859 name is "mtdblock3" rw yaffs: passed flags "" yaffs: yaffs: Attempting MTD mount of 31.3,"mtdblock3" yaffs: auto selecting yaffs2 yaffs: yaffs_read_super: is_checkpointed 0 yaffs: dev is 32505857 name is "mtdblock1" rw yaffs: passed flags "" yaffs: yaffs: Attempting MTD mount of 31.1,"mtdblock1" yaffs: auto selecting yaffs2 yaffs: yaffs_read_super: is_checkpointed 0 yaffs: dev is 32505860 name is "mtdblock4" rw yaffs: passed flags "" yaffs: yaffs: Attempting MTD mount of 31.4,"mtdblock4" yaffs: auto selecting yaffs2 yaffs: yaffs_read_super: is_checkpointed 0 # remove unnecessary files... ############################ fuse init (API version 7.8) ip_tables: © 2000-2006 Netfilter Core Team ip6_tables: © 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1752 buckets, 14016 max) ctnetlink v0.93: registering with nfnetlink. ip6t_ROUTE: module license 'unspecified' taints kernel. ipecs_misc: installed(drv=1.1.2, fpga=3)... options: c1k_eth_open: eth2 Disabling GEM1 delay PHY start: 1:02 fpp_running=365 voib_installed=0 eth2_running=61 Installing DCI modules... CSM Driver version 4.08.1cvs 13:22:37 Jul 24 2013 Comcerto 1000 architecture Comcerto 1000 architecture Comcerto 1000 architecture Comcerto 1000 architecture csm: found csm type 9 (minor 0, index 0) csm: found csm type 9 (minor 1, index 1) IP Interface Driver version 1.0 13:22:39 Jul 24 2013 Matisse Driver version 4.08.1cvs 13:22:32 Jul 24 2013 MSP is running drivers/net/comcerto/comcerto_ved.c: 577: info Device=170 Revision=0 spu_version=Arm11DspV_5_6_98 CSPtoMSPQueuePhyaddr=a000500 MSPtoCSPQueuePhyaddr=a000510 SMRXCSPhyaddr=a000520 SMTXCSPhyaddr=a000520 MSP version is : Test_74757_1 ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/none/1.1.2.2 loaded PPP BSD Compression module registered ipecs_rtc: installed... ipecs_sram: hd_sect=512, nsect=51200 ipecs_sram: major number = 254 - wrap_init: device wrap malloc=40000 for 8192 nodes - wrap_init: device stat malloc=18000 for 8192 nodes ipecs_sram: installed(size=25MB), v=3.0.0.0 membuf: pa/va=8e300000/d0000000 :: sram wrapper kthread, entry, dev=ce241000 ipecs_e2p: installed(drv=1.0.0, fpga=3)... ipecs_env: installed(env_valid=1)... SPI core: add adapter comcerto-spi SPI core: add driver ipecs_spi SPI core: attach client to adapter comcerto-spi ipecs_spi: installed(ver=1.2.0)... ipecs_wdog: installed(2.0Aa, wdog-tmr), HZ=200 isdnloop-ISDN-driver Rev 1.11.6.7 Register LDKPPP Device Driver. ver=1.0Aa isdnloop: (loop0) virtual card added ipecs_net: local dev name=eth0 ipecs_net: dsp dev name=eth1 ipecs_net: loop dev name=lo ipecs_net: VVMU/VOIB48 dev name=eth2 net device ptr: eth=cda13000 dsp=c03dd81c lo=c03ddf9c eth2=cda6a800 vlan=0 ipecs_net: installed (HZ=200, ms=5) revision: 3.5Ca, SRTP-SESSION-TRAIN ipecs_dpram: installed, dpram map: xxxx... REGISTER devAct2 device 0.1.1 OK REGISTER devSlot device 0.1.1 OK [FPGA Iss.3] CMU Detection lco_io_base[0][4] = 0xce70000f REGISTER devLco device 0.1.12 OK REGISTER devTimer device 0.1.1 OK ISDN Drv Ver:A.0Ad-b03 Date:27 JUL 2015 REGISTER device ipecs_pri 0.0.2 OK Register device ipecs_igpio 0.0.1 OK REGISTER device ipecs_bri 0.0.1 OK [IDEV]dev_irq_status = ce800006(ff) [BDEV]basic borad id = FF [BDEV]opt1 borad id = FF [BDEV]opt2 borad id = FF [BDEV]brib_opt1_io_base = ce0d0000 [BDEV]brib_opt2_io_base = ce0d4000 [BDEV]brib_basic_io_base = ce0d8000 [BDEV]peb_io_base[0] = ce0d8200 [BDEV]peb_io_base[1] = ce0d8300 [BDEV]peb_io_base[2] = ce0d0400 [BDEV]peb_io_base[3] = ce0d0600 [BDEV]peb_io_base[4] = ce0d4400 [BDEV]peb_io_base[5] = ce0d4600 [PDEV]fpga_base_address = ce0c8000 [PDEV]pef_base_address = ce0c8100 [PDEV]c5402_base_address = ce0c8200 [PDEV]dev_brd_id = ce0c8000 [PDEV]dev_cntry_var = ce0c8000 [PDEV]dev_brd_iss = ce0c8001 [PDEV]dev_fpga_ver = ce0c8002 [PDEV]dev_pp_reset = ce0c8003 [PDEV]dev_dip_sw = ce0c8004 [PDEV]dev_led1 = ce0c8005 [PDEV]dev_led2 = ce0c8006 [BDEV]Line Mode : FF(1:T, 0:S) [BDEV]Slot#0 BrdId=0x1F=>0x00 [BDEV]Slot#1 BrdId=0x1F=>0x00 [BDEV]Slot#2 BrdId=0x1F=>0x00 ipecs_timer: installed(1.0.0, hwtmr=5ms)... ippp0 added Encapsulation for ippp0 is syncppp EAZ/MSN for ippp0 is 100 Layer-2-Protocol for ippp0 is hdlc Hangup-Timeout for ippp0 is 180 sec. -+ isdnloop_command:1276: carrier off... carrier=0 done kernel.msgmni = 32 net.ipv4.ip_nonlocal_bind = 1 net.ipv4.tcp_keepalive_time = 60 net.netfilter.nf_conntrack_udp_timeout = 1 VOIB: board is not installed... [app.tar.gz] is not exist. skip app extraction. end of app file extraction. end of html file extraction. isdnloop: (loop0) DRV1.23EC-Q.931-CAPI-CNS-BASIS-20.02.96 isdnloop: (loop0) Euro-Protocol loaded and running g_fdDipSw = 3 dip = b ipmethod = dhcpContinue stop DHCP wait 3 sec DHCP Loop End ########################################################### ########################################################### [iPECS Loader] Apploader Start [iPECS Loader] Loading the Loader File [iPECS Loader] Autoloader Execute /home/http/_main_app2.rom from the loader file Starting System Initialization... mainsub_start_itimer::::: magic number=3355aacc time=2000 -> 10 > application init. started... [BOARD_INFO] board=iPECS eMG80, co_opt=NONE [BOARD_INFO] No_Of_Stns[140] No_Of_Cols[74] No_Of_Stns_And_Cols[214] IpExtensionTotalNumFlag[0] Q[7]-[0] msg_key[6b:107] maxmsg[200] X msgsize[970] = Qsize[194000]->[194000]->msg_qB[194000] Q[12]-[8001] msg_key[70:112] maxmsg[200] X msgsize[1024] = Qsize[204800]->[204800]->msg_qB[204800] Q[13]-[10002] msg_key[71:113] maxmsg[400] X msgsize[1024] = Qsize[409600]->[409600]->msg_qB[409600] Q[11]-[18003] msg_key[6f:111] maxmsg[1050] X msgsize[32] = Qsize[33600]->[33600]->msg_qB[33600] [DevMisc_Init]FPGA VER : 3 open ipecs_spi file : g_fdSpi 8 DevMisc_Init!!! (Codec:A-law) DevAct2IO_Init!!! DevAct2IO_Init!!! DevLcoIO_Init(1)!!! DevLcoIO_Init(2)!!! DevLcoIO_Init(3)!!! DevLcoIO_Init(4)!!! DevLcoIO_Init(5)!!! DevLcoIO_Init(6)!!! DevLcoIO_VoipDtmf!!! MGIO_Initialize!!! g_fdRTC(128) open /dev/ipecs_rtc SRAM_INIT: sram DB, init... [PROT_INIT] driver major #=254 [PROT_INIT] db: prefix=__DB_file__ [PROT_INIT] db: configuration file=__DB_file__config_ [PROT_INIT] db: create partitions... [PROT_INIT] db: open partitions... elapsed time=1.182s [PROT_INIT] db: mmap(size=0x72c000)... [PROT_INIT] db: msync bitmap, max=1836 [PROT_INIT] db: mmap=40004000 size=0072c000 [PROT_INIT] db: PROT_END - PROT_BASE = 0072b330 - 00001000 = 0072a330 [PROT_INIT] db: ADDR_END - ADDR_BASE = 40730000 - 40005000 = 0072b000 SRAM_INIT: sram DB, mmap=40004000 size=0072c000 [Dev_Init_Task] starting init. DB ptr [Dev_Init_Task] ending init. DB ptr 0x4072f330 - 0x40005000 = 72a330 = 7336 KB ------- SYS_EMG: TODO!!!: VLAN SET -------- main_sub.c:1712 DHCP OFF by env(kill dhcpcd)!!! [GetMACAddrEth0:679] b0:61:c7:3:b6:72 Mfim_ip_addr=a0a0a02 Mfim_net_mask=ffffff00 Mfim_firewall_ip_addr=0 [SYS_CTRL] lan1: net=10.10.10.2/255.255.255.0/10.10.10.1 [INIT ETH2: ifconfig Return(0)] ip: 1020304, net mask:0, gateway: 0, mac:00:40:5a:00:00:01 VAINIT : dev(ipfilter), ver=3.5Ca, SRTP-SESSION-TRAIN [ONE_IP] setup q931 ports range: 2048..2559 [ONE_IP] setup h245 ports range: 2560..3071 [ONE_IP] setup ras ports range: 2048..3071 [ONE_IP] setup sip tcp ports range: 3072..4095 VAINIT : CSMENCAPS TYPE(0) [DCI_RcvThread] Comcerto 1000 architecture started [DCI_OPEN] device state=0, resetting... [DCI_OPEN] open dev=294 ############################################################################ ### ### ### ======================== DSP's Info. =============================== ### ### ### ############################################################################ ST 1 : query about dev_type : 0x53, m83xxx ST 2 : query about dev_version : rev. A ST 3 : query about msp armcode_version : Test_74757_1 ST 4 : query about msp spucode_version : Arm11DspV_5_6_98 ST 5 : spucode_version verification : passed! ST 6 : initialize remain dsp parts... ST 7 : rtp ports(4): (7000, 7015) (7100, 7115) (7132, 7147) (7200, 7299) ST 8 : end of dsp init. [SYS_CTRL] system dynamic port range: 4096..6095 ------- SYS_EMG/UCP: TODO!!!: main_sub.c:3546 [ips init]entering ptKTSProtInitialize [GetMACAddrEth0:679] b0:61:c7:3:b6:72 Q[4]-[40008] msg_key[68:104] maxmsg[10] X msgsize[1024] = Qsize[10240]->[10240]->msg_qB[10240] Q[6]-[48009] msg_key[6a:106] maxmsg[120] X msgsize[1024] = Qsize[122880]->[122880]->msg_qB[122880] Q[0]-[5000a] msg_key[64:100] maxmsg[180] X msgsize[1024] = Qsize[184320]->[184320]->msg_qB[184320] Q[3]-[5800b] msg_key[67:103] maxmsg[60] X msgsize[1024] = Qsize[61440]->[61440]->msg_qB[61440] [ptInitTCPConnInfoHash] g_tTCPConnInfoSema = (nil) [ptInitTCPConnInfoHash:1665] g_tTCPConnInfoSema[(nil)] wait [ptInitTCPConnInfoHash:1671] g_tTCPConnInfoSema[(nil)] post Q[4]-[40008] msg_key[68:104] Qsize[16384]->msg_qB[10240] [ips_init] net0 bind address: 10.10.10.2:5588 [ips_init] net1 bind address: 1.2.3.4:5588 Q[6]-[48009] msg_key[6a:106] Qsize[16384]->msg_qB[122880] [ips init]ret, ptKTSProtInitialize = 0 [ips init]entering ptMsgQOpen-RX Q[0]-[5000a] msg_key[64:100] Qsize[16384]->msg_qB[184320] [ips init]entering ptMsgQOpen-TX [ips init]entering ptMsgQOpen- CR TX [ips init]entering ptMsgQOpen- CR RX Q[3]-[5800b] msg_key[67:103] Qsize[16384]->msg_qB[61440] Q[8]-[6000c] msg_key[6c:108] maxmsg[2600] X msgsize[1280] = Qsize[3328000]->[16384]->msg_qB[16384] [VINFO] (-1) vm_Initialize, check crypto function -> ok [VINFO] (-1) vm_Initialize, srtp supporting -> 1 [VINFO] (-1) vm_Initialize, set the bit for the srtp supporting... [VINFO] (-1) vm_Initialize, crypto supporting2 -> 0x3 [VINFO] (-1) vm_Initialize, create VOIP GW thread... (INIT_H323) HBINFO: network, local-ip=10.10.10.2 (INIT_H323) HBINFO: network, wan-ip=10.10.10.2 (INIT_H323) HBINFO: network, media-ip=10.10.10.2 (INIT_H323) HBINFO: Iinit. with endpoint type : GATEWAY... Q[10]-[80010] msg_key[6e:110] maxmsg[1000] X msgsize[180] = Qsize[180000]->[180000]->msg_qB[180000] (INIT_H323) HBINFO: End of init., w/o GK config... EKSU Not Installed!!! BKSU PP/ACT2 Reset! Act2(#0) GSXD Init OK Act2(#0) DBID Init OK Act2(#0) GSL12 Init OK [AsicDspMemoryCheck]Code Compare Success!!! First Main Act2 Init-Complete Ver(1.6) SLOT7(0x00) ResetSpiLco:BMBU LCO/SLT(0xf7)!!! tmpBoardId(S#0) = 0x1 [SLIB] SLOT0 DuSLIC feeding power ON! tmpBoardId(S#1) = 0xff tmpBoardId(S#2) = 0xff tmpBoardId(S#3) = 0xff tmpBoardId(S#4) = 0xff tmpBoardId(S#5) = 0xff MBU LCOB INSTALLED tmpBoardId(S#6) = 0x8 tmpBoardId(S#7) = 0xff tmpBoardId(S#8) = 0xff tmpBoardId(S#9) = 0xff tmpBoardId(S#10) = 0xff tmpBoardId(S#11) = 0xff SLOT0 VOIB8 Dev-malloc() success SLOT0 VOIB8 Dev-malloc() success NIPP : g_usNationCode = 82ff [KOR:82ff] NIPP : OptionBID = ff [NONE] UCP : Spi device file open UCP : devSpi open SUCCESS! UCP100 Nipp Channel : fxs=2, fxo=0, fxd=8, fxc=0 UCP100 FXC start Channel : 10 g_siMCSocket : 439 DUAL_FILTER_ECAN >>> FALSE [IDEV]ipecs_igpio Open [BAPP]igpio file [IBDEV]BRIU=0x1F open : 0x1B8 [IBDEV]BRIU_Type=0x07 [BAPP]BRIU board [IBDEV]BH2/1#1=0x1F id:0x1F, type:7 [IBDEV]BH2/1#1_Type=0x07 [BAPP]BH2/1#1 bo [IBDEV]BH2/1#2=0x1F ard id:0x1F, typ [IBDEV]BH2/1#2_Type=0x07 e:7 [BAPP]BH2/1#2 board id:0x1F, type:7 [BAPP]Total BCH Num:0 Wrapup Task Interval = 3 => 30 msec LED Task Interval = 12 => 120 msec LCD Task Interval = 30 => 300 msec iPKTS Retransmission = 4 LEDLCD Devide Number = 3 Kernel :: Kernel Version is [R1.1.13] in rc file. [SDC_Init_Port] ttyS0, fd=441, br=115200, hflow=0, xon/off=0 [SDC_Init_Port] ttyS1, fd=442, br=115200, hflow=0, xon/off=0 [SDC_Init_Port] ttyUSB0, fd=-1, br=115200, hflow=0, xon/off=0 [SDC_Init_Port] ttyUSB1, fd=-1, br=115200, hflow=0, xon/off=0 iPECS eMG80 System. Copyright © 2012 Ericsson-LG Enterprise. Port Name:COM1 Date: 07/09/16 Time: 08:28:30 Version: eMG80-R2.1.23, Checksum: 0 SW1 BACKUP DATABASE: THE SYSTEM DATABASE WAS NOT RESTORED TO DEFAULT! * Reset_cnt = 47 ############## Last Reset Cause = POWER OFF ############### ########### NO LAST log ############## Last Reset Cause = POWER OFF ############### ------[main_sub.c:InitSystemResource:2081] msync: all=3 range=8379 ------[main_sub.c:InitSystemResource:2086] init. time DB msync all: elapsed time=0.000s [GetMACAddrEth0:679] b0:61:c7:3:b6:72 eth0: c1k_eth_close c1k_eth_open: eth0 Disabling GEM0 delay PHY start: 0:01 ADDRCONF(NETDEV_UP): eth0: link is not ready [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1151 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1155 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1159 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1163 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1167 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1171 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1175 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1179 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1182 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1186 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1189 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1214 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1230 Status:0 ---- DPRAM: 0 0 0 0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1255 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1266 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1271 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1283 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1288 Status:0 *** Start nippmg_thread *** [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1291 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1308 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1312 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1317 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1324 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1332 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1338 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1341 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1347 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1353 Status:0 [DEBUG] File:main_sub.c,Func:Create_AppTasks(),Line:1358 Status:0 *** Start NIP PRIB Main *** *** Start LLDP-MED *** -+ LLDPService: add LLDP MAC A lldp Comp : 2016/11/09 09:30:44 by bhchoi lldp Date : 2016/11/09 09:30:44 lldp year : 2016, month : 11, day : 09 RdPsysDiffServPreTaggingMfim : 4 RdPsysVlanOnOff : 0 RdPsysVlanPriority : 0 RdPsysVlanId : 0 *** Start nippmg_slib_task *** nippmg_slib_semaphore init ret=0 [XMLHttpWebserverStart] : >>>>>>>>>>>>>>>> [RegisterNippBoard] P_Slot[12].CallBoardId = 0x0 [RegisterNippBoard] P_Slot[13].CallBoardId = 0x0 startNippBoardEvent ------ mmap tmr start... [MODU PPP] options.ttyS1 to be updated AAAAAAA OSS ASN.1 (QSIG) is initialized. [MODU PPP] tty1_options, result = 740 AAAAAAA OSS ASN.1 (H450) is initialized. [VSF] misc_vsf task Start ... [GetMACAddrEth0:679] b0:61:c7:3:b6:72 brim task will be terminated !! isdn_free_channel: called with invalid drv(-1) or channel(-1) ******************************** * Option MEMU : not installed * ******************************** mkdir: can't create directory '/var/lock': File exists [MODU PPP] ifconfig ippp0 down [VSF] old usr msg header conversion start... [Nipp PRIB] Can't Open Driver!!! fNippIsrStart [VSF] old usr msg header conversion finished, total_usr_msg=0, converted=0, time=356 msec SLT ports Duslic Initial Results ---------------------------------------- SLOT port Duslic_status ---------------------------------------- SLOT0 00..07 30 30 30 30 30 30 30 30 SLOT1 10..0f SLOT2 20..1f SLOT3 30..2f SLOT4 40..3f SLOT5 50..4f ---------------------------------------- Duslic fault : 0 port(s) PHY: 0:01 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready -------------------------------------------------------------------------------------------------- Подскажите, что делать? Сонсолью тоже соединялся PuTTY. Авторизуюсь j...., (1234 - не подходит) но никаких пунтных подстазок нет. Системного аппарата тоже нет( |
|
|
22.2.2017, 18:35
Сообщение
#2
|
|
ГУРУ Группа: Модераторы Сообщений: 15007 Регистрация: 19.6.2009 Из: г. Тула Пользователь №: 13420 |
Вероятно, рекавери поможет. К сожалению, у меня нет.
Из каких же таких соображений вы обесточили АТС в процессе ее обновления? Кнопочка Reset не просто так же сделана... -------------------- Вот смотрю я на вас и думаю: ещё выпить, или вы мне уже нравитесь? Анекдот
|
|
|
22.2.2017, 18:44
Сообщение
#3
|
|
ГУРУ Группа: Модераторы Сообщений: 15007 Регистрация: 19.6.2009 Из: г. Тула Пользователь №: 13420 |
Вероятно, рекавери поможет. К сожалению, у меня нет. Из каких же таких соображений вы обесточили АТС в процессе ее обновления? Кнопочка Reset не просто так же сделана... А SW1.2 переводили в OFF после выставления страны и перезагрузке? Перезагружали с SW1.2 = ON для сброса настроек по дефолту? -------------------- Вот смотрю я на вас и думаю: ещё выпить, или вы мне уже нравитесь? Анекдот
|
|
|
23.2.2017, 20:30
Сообщение
#4
|
|
Участник Группа: Участники Сообщений: 18 Регистрация: 24.1.2017 Пользователь №: 20544 |
А SW1.2 переводили в OFF после выставления страны и перезагрузке? Перезагружали с SW1.2 = ON для сброса настроек по дефолту? Ну нативно кнопка резет выглядит как отменить все изменения на странице. Вот почему. SW1.2 был всю дорогу в ON. После потери связи со станцией он был уже и в ON и в OFF. Но ничего путного не вышло. |
|
|
23.2.2017, 20:32
Сообщение
#5
|
|
Участник Группа: Участники Сообщений: 18 Регистрация: 24.1.2017 Пользователь №: 20544 |
Спасибо отзывчивым людям.
Буду заниматься рекавери. |
|
|
27.2.2017, 12:34
Сообщение
#6
|
|
Участник Группа: Участники Сообщений: 18 Регистрация: 24.1.2017 Пользователь №: 20544 |
Залил рекавери. Все ожило.
Спасибо. |
|
|
28.2.2017, 14:39
Сообщение
#7
|
|
Ветеран форума Группа: Участники Сообщений: 1166 Регистрация: 29.8.2007 Из: Москва Пользователь №: 4065 |
Я так подозреваю что удалили файлы перед UPGRADE.
Это делать не надо. |
|
|
Текстовая версия | Сейчас: 27.4.2024, 8:42 |